Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

See Answer
*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.

You are watching: Determine the resultant force and specify where it acts on the beam measured from a.


Q: How does the existence of sprinkler systems affect building code enforcement?

A: Sprinkler system is a fire fighting system, fix at one position in the building . It is automatic s...


Q: A four-lane freeway (two lanes in each direction) is located on rolling terrain and has 12-ft lanes,...

A: Given above data we have to find the maximum number of large trucks and buses


Q: The cantilevered beam shown in the accompanying figure is used to support a load acting on a balcony...

A: w = distributed load (N/m)=10,000 N/mE = modulus of elasticity (N⁄m2 )=200 GPaI = second moment of...


Q: Problem 3For the shown beam.(1) Plot V and M diagram(2) Find the maximum tensile and compressive ...

A: Click to see the answer


Q: HW: Determine the force in each member of the truss shown in Fig. below. Indicate whether themember...

A: Click to see the answer


Q: A square box beam is made of two 20× 80-mm planks and two20 x120-mm planks nailed together as shown...

A: GivenV=1200NS=30mm


Q: WHEN A LOWER (e.g., 1060') CONTOUR IS REROUTED TO MOVE CLOSER TO A HIGH (e.g.,1065') CONTOUR , THE C...

A: Contours are the point joining equal elevation. 


Q: An interior wall of a building is made up of metal studs with 5/8 in. wallboard on each side. See t...

A: Given:Width of the metal studs=58inWidth of the stud=338inThen,Width of metal studs 58in on both si...


Q: 3)A- SteelThe allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod ...

A: Click to see the answer


Q: Briefly identify what requirement of the strength is for a structural system and for a member of a s...

A: Strength is very important for structural member , strength is nothing but the ability of a member t...


Q: Refer to Problem 3.8. Determine the mass of water (in kg) to be added per cubic meter (m3) of soil f...

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in effe...


Q: 3. The graph below shows a typical section of a steel plate bridge girder. Caleulate themoments of ...

A: Solution


Q: Classify the following soils, A through E, using the Unified Soil Classification System,including t...

A: GIVENthe value of soil data to find the type of soil 


Q: A saturated cohesive soil has the following characteristics:Initial Volume = 33.5 cm3Final Volum...

A: Given: Initial Volume = 33.5 cm3Final Volume = 21.6 cm3Mass of Wet Soil = 60.0 gMass of Dry Soil...


Q: 4-7.Determine the internal normal force, shear force, andbending moment at point D. Take w =150 N...

A: Given data Length of AB & BCUDL 


Q: The 2014-T6 aluminum strut is fixed between thetwo walls at A and B. It has a 2 in. by2 in. square...

A: GivenT1=23lb ftT2=38lb fta=2inT6 aluminium


Q: A 10× 14 beam of Hem Fir select structural grade is loadedsymmetrically with three concentrated load...

A: As per the given dataDue the symmetry RA = RB = 4300x32 = 6450lb SFD - 


Q: What is a collapse zone? And how big is it?

A: The collapse zone is defined as "the area which is covered near the structure going to collapse". Th...


Q: 3. A rocket accelerates by burning its onboard fuel, so its mass decreases with time t. Suppose the ...

A: Click to see the answer


Q: Temperature has a large effect on the asphalt viscosity. On one graph, plot the relationship between...

A: The temperature has a prominent effect on asphalt cement concrete. At high temperature, the asphalt ...


Q: To loosen a frozen valve, a force F of magnitude 90 lb is applied to the handle of the valve. Knowin...

A: Given,Force, F=90lbθ=25oMoment about x-axis, Mx=-61lb.ftMoment about z-axis, Mz=-43lb.ft


Q: 4)Under normal operating conditions, a motorexerts a torque of magnitude Tf at F. Theshafts are m...

A: Diameter of shaft FGH d1=0.8 inradius r1=0.4 inand radius of gear rG=4.5 indiameter of shaft CDE ...


Q: How does ecological site design contribute to the goal of Zero Net Energy (ZNE) in buildings? Provid...

A: If the total energy used by the building on an annual basis is equal to the amount of energy generat...


Q: Draw the moment diagrams for beam using the method of superposition. Consider the beam to be cantile...

A: Solution:As per the free body diagram ∑MA=0By×8-20×11-40×8×82-150=0By=206.25kN∑Fy=0Ay+By=40×8-20A...


Q: The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown. If the ...

A: Calculate the modulus of elasticity of the composite beam:m=EstEbr =200100 m=2Calculate the dis...


Q: For an unconfined compressive strength test on a soil having USCS classification of CH and sample di...

A: Click to see the answer


Q: A motorcyclist at A is traveling at 60 ft/s when he wishes to pass the truck T which is traveling at...

A: The overtaking sight distance is defined as the minimum distance to the vision of the driver of the ...


Q: Describe properties that represent how light or how heavy materials are per unit volume.

A: Properties of light or how heavy materials are, generally rely on the mass of the material. Some kin...


Q: Determine the strain at yield of a Grade 60 #14 rebar (ASTM A 615). How does this compare to the str...

A: (ASTM A 615) with Grade 60 #14& Grade 60 #5


Q: Water (assumed inviscid and incompressible) flows steadily from the large tank shown in thefigure b...

A: D1=1m=D2To find discharge and air pressure


Q: A saggar is a ceramic, boxlike container (round, oval or cubic in shape) used in the firing of ceram...

A: When developing a new glass melt, it is critical that the right crucible is chosen to ensure that th...


Q: A piece of duct measures 24 inches. When 2 pieces are fitted together, 11⁄2inches are allowed on eac...

A: Consider the free body diagram;


Q: 10.9 Water flows in the pipe shown, and the manometer deflects90 cm. What is ffor the pipe if V = 3...

A: Click to see the answer


Q: A pin-connected structure is supported and loaded as shown below. MemberABCD is rigid and is horizo...

A: Click to see the answer


Q: Which of the following is NOT a benefit of using SCMs?Increase required concrete curing timeIncre...

See more: Bring It On Home By Sonny Boy Williamson Ii Bring It On Home

A: Supplementary cementing materials are generally added to concrete to make concrete mixtures more e...